Маркуч за фугиране на бетонни фуги в съответствие с указанията на WU -> MASTERTUBE Yellow Комплект за полагане | 10 м

MASTERTUBE Yellow Комплект за полагане | 10 м

Name: MASTERTUBE Yellow Комплект за полагане | 10 м
Brand: Mastertec
SKU: 030055

Готов комплект, състоящ се от: 10 м инжекционен маркуч MASTERTUBE, вкл. монтажен материал

номер на статията 030055

Маркуч за фугиране на бетонни фуги в съответствие с указанията на WU

Produktbeschreibung

При уплътняване на фуги на бетонни конструкции се поставят високи изисквания към технологията на уплътняване.

Инжекционният маркуч MASTERTUBE гарантира, че хоризонталните и вертикалните бетонни строителни фуги могат да бъдат надеждно и трайно уплътнени срещу вода под налягане и без налягане.

Монтажният комплект включва:

10 м MASTERTUBE ЖЪЛТ инжекционен маркуч

2 фиксиращи пакети

100 пластмасови скоби за закрепване тип В

2 съединителя за маркуч

Получете оферта сега Добавяне към списъка с известия

Забележка: Съдържанието на тази страница е преведено автоматично и може да съдържа грешки. Ако се съмнявате, вижте английската или немската версия или попитайте нашия екип.

Най-важната информация с един поглед

Ценова листа

Технически данни

номер на статията:

030055

група артикули:

301 - Injektionsschlauch Verlegeset

GTIN:

4251689514210

номер на митническата тарифа:

39172190

опаковъчна единица:

Задайте

продажба на количество единица:

1 Set

тегло на:

Задайте = 1 kg

материал:

PVC маркуч

Обхват на доставката:

10 м MASTERTUBEm ЖЪЛТ инжекционен маркуч

2 закрепващи пакети

100 пластмасови скоби за закрепване тип В

2 съединителя за маркуч

съхранение:

Да се съхранява в неповредена и неотворена оригинална опаковка на сухо място, далеч от пряка слънчева светлина.

изхвърляне:

Can be disposed of at municipal waste
landfill sites, taking into account the
local waste disposal regulations.

Лист с данни

Ръководство за инсталиране

Installation of injection hose

The injection hose MASTERTUBE “YELLOW” serves as internal waterproofing of construction joints.

-The length of the hose sections must not exceed 15 m. Shorter injection hose sections facilitate later injection.

- The injection hose is installed in the centre of the construction joint or – in case of constructional elements with a thickness of > 60 cm – at a distance of 15 cm from the water-remote side of the structure.

- Ensure a distance of 8 cm from the edge on all sides.

The concrete surface which the MASTERTUBE “YELLOW” is to be installed on must be as follows:

- clean and free from cavities

- free from loose particles and cement slurry

- free from release agents or other components that are separating or interfering with the adhesive bond

- free from ice and standing water

MASTERTUBE “YELLOW” is supplied as rolls of 100 m length.

Cut the hose with a suitable cutting tool. Prior to cutting, mask the cutting section with 2 – 3 wraps of filament tape, which prevents the hose from tearing in longitudinal direction.

Fastening packers are screwed into the ends of the injection hose sections up to the thread end and fixed to the formwork surface. The position of the fastening packer should ensure permanent accessability (floor structure and Technical Building Equipment must be taken into consideration). The fastening packers have closure plugs in 2 different colours. These are used for marking of the pairs used for the individual hose sections.

Successive injection hose sections must overlap by at least 10 cm to ensure continuous injection of the joint. The distance between parallel injection hoses must be min. 5 cm. Otherwise during injection of one hose section, the adjacent hose section might accidentally be filled as well.

If the distance of 5 cm cannot be provided in any subsection, this part of one of the hoses needs to be completely wrapped with filament tape in order to prevent accidental injection.

Alternatively, you may use injection end pieces instead of the fastening packers. These are 50 cm long unslit hoses with fabric sheath. By use of hose connectors the injection end pieces are screwed into the ends of the injection hose sections up to the thread. Fixing to the formwork surface is done by use of storage boxes, which the injections end pieces are led into and stored until later injection. The connection point between injection hose and injection end piece must be surrounded on all sides by at least 10 cm of concrete.

The position of the storage box should ensure permanent accessability (floor structure and Technical Building Equipment must be taken into consideration). The injection end pieces are available in 2 different colours. These are used for marking of the pairs used for the individual hose sections.

If the distance of 5 cm cannot be provided in any subsection, this part of one of the hoses needs to be completely wrapped with filament tape in order to prevent accidental injection

MASTERTUBE “YELLOW” must be fixed in such a way that it cannot shift neither before nor during concreting. It can be fastened by using metal clips or plastic fastening clips. The distance between either type of clips must not be more than 15cm in longitudinal direction. On very uneven surfaces and at each change of direction, the distance should be halved.

Changes of direction must be carried out with a sufficient bending radius in order to avoid damage to the hose or an obstruction of the overall injection.

The radius must be minimum 5 cm.

When changing between horizontal and vertical installation direction, the injection hose must be routed right into the corner of the joint and routed upwards via a loop. The minimum radius as well as the concrete cover need to be observed.