fra natriumbentonitt
artikkelnummer 010020
Produktbeskrivelse
.
MASTERSTOP bentonitt svellende tape har blitt utprøvd og testet i byggepraksis i årevis, sveller ved kontakt med vann og tetter sprekker eller konstruksjonsfuger på en sikker og permanent måte.
.
Testene sikrer at produktet er egnet for de ulike bruksområdene.
- Enkel og sikker montering
- Ingen støpte deler og sveiser
- Ingen oppstandere
- Svelling og krympingsprosessen er reversibel
- Selvinjiserende effekt Dimensjonsstabil og ikke-klebrig
- De svellende båndene trenger inn i sprekker og hulrom
- Ingen avfall eller restbiter
- Miljøvennlig
- Sikker takket være omfattende testing
Den viktigste informasjonen på et øyeblikk
Natriumbentonitt med gummiinnhold
Smooth
plast
20 x 15 mm
Opp til 340 % i vanlig vann (pH 7)
Opp til 160 % i væsker som
opp til 160 % i væsker som angriper betong sterkt
.
opp til 140 % i alkaliske væsker
Nei
Ja
Nei
Ja
Generell prøvingsattest fra bygningsmyndighetene (abP)
MFPA Leipzig
Nr.: P-SAC 02 / 5.1 / 12-057
Europeisk teknisk vurdering
ETA - 16 / 0735
datert 13. september 2017
Ja
Bruk klasse A for belastningsklasse 1 og 2 i samsvar med WU-retningslinjene
Kan deponeres på deponier eller forbrenningsanlegg i samsvar med lokale forskrifter for avfallshåndtering.
Installation with swelling tape adhesive:
The substrate must be clean, dry, and free of loose particles.
Apply the swelling tape adhesive in the centre of the joint in a uniform bead (width 8-10 mm) out of the cartridge onto the surface.
The subsequent concrete covering must be at least 8 cm on all sides.
Once the swelling tape adhesive has been applied in the centre of the joint, the MASTERSTOP bentonite swelling tape is placed on the adhesive and gently pressed on, moving it slightly back and forth, crosswise to the longitudinal axis.
When the tape is fixed, the adhesive should slightly ooze out on both sides.
This guarantees a complete fixation.
Ready for use after 4 – 6 hours (depending on weather conditions)
Installation with swelling tape grid:
The substrate must be clean, dry, and free of loose particles.
Place the MASTERSTOP bentonite swelling tape in the centre of the joint.
The subsequent concrete covering should be at least 8 cm on all sides.
Position the swelling tape correctly.
Push the fixing grid firmly onto the MASTERSTOP bentonite swelling tape.
Fasten using corresponding nails and either by hand or mechanically using a bolt-firing tool.
The distance between nails must not exceed 20 cm in the longitudinal direction of the swelling tape.
Both, straight and angle joints need to be butt jointed.
The joint areas must be form-fit in order to avoid any discontinuity in the system.
In the case of butt joints in the straight line and the use of swelling tape grids, the joints of swelling tape and swelling tape grid should be offset.
Status: 23.03.2022
Tilbehør
egnet tilbehør
Enkomponent, løsemiddelfri tetningsmasse for liming av MASTERSTOP bentonitt svellende tape . Forbruk: 40 - 50 ml/m ...
Lignende produkter
Du finner lignende produkter her.
Dette er en test...
Kontakt oss
Vi svarer gjerne på spørsmålene dine