Dimension Ø ca 5/10 mm
artikelnummer 030050
MASTERTUBE Insprutningsslangsystem
Tätning av konstruktionsfogar i betong ställer höga krav på tätningstekniken.
MASTERTUBE injekteringsslang säkerställer att horisontella och vertikala betongkonstruktionsfogar kan tätas på ett tillförlitligt och permanent sätt mot trycksatt och icke trycksatt vatten. Lägg till i meddelandelistanDen viktigaste informationen i en överblick
PVC innerslang
.
Mantel av monofilamentväv
ca. 10 mm
ca. 5 mm
Slit, med ventilfunktion
depending on injection agent,
approx. + 6°C to +40°C
Allmän byggnadsmyndighets testcertifikat (AbP)
MFPA Leipzig
Nr: P-SAC 02 / 5.1 / 21 - 266-1 (PU-harts)
Nr: P-SAC 02 / 5.1 / 21 - 266-2 (akrylat)
Upp till max. 2 bar ( 20 m vattenpelare )
Ja
Användningsklass A för lastklass 1 och 2 i enlighet med WU:s riktlinjer
1 Rolle på 100 m
.
The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.
After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.
Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.
The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.
Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.
Fixing on joints with category "rough"
On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.
Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.
All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.
Status: 23.03.2022
HOSE CONNECTOR / VENTILATION HOSE / SEALING PLUG / STORAGE BOX in in-situ concrete
Ladda ner DWG Ladda ner PDFTillbehör
lämpliga tillbehör
Med MASTERTECs infästningspackning kan injekteringsslangen fästas direkt på formen. Fästpaketet möjliggör ekonomisk infästning oc...
Fästklämma för flytsäker installation av injektionsslangar på betongytor ...
Polyuretanharts för injektering av slangar och sprickor ...
Liknande produkter
Du hittar liknande produkter här.
Tätning av konstruktionsfogar i betong ställer höga krav på tätningstekniken.MASTERRÖRET "GUL" säkerställer att horisontel...
Kontakta oss
Vi svarar gärna på dina frågor