Rozmer Ø približne 5/10 mm
číslo článku 030050
Systémy vstrekovacích hadíc MASTERTUBE
Tesnenie škár betónových konštrukcií kladie vysoké nároky na technológiu tesnenia.
Injektážna hadica MASTERTUBE zabezpečuje spoľahlivé a trvalé utesnenie horizontálnych a vertikálnych betónových stavebných škár proti tlakovej a netlakovej vode. Pridať do zoznamu upozorneníNajdôležitejšie informácie na prvý pohľad
Vnútorná rúrka z PVC
Opláštenie ako monofilová tkanina
cca. 10 mm
cca 5 mm
Svietidlo s funkciou ventilu
depending on injection agent,
approx. + 6°C to +40°C
Osvedčenie o skúške všeobecného stavebného úradu (AbP)
MFPA Lipsko
Č.: P-SAC 02 / 5.1 / 21 - 266-1 (PU živica)
Č.: P-SAC 02 / 5.1 / 21 - 266-2 (akrylát)
Do max. 2 barov (20 m vodného stĺpca)
Ja
Triedu A použite pre triedy zaťaženia 1 a 2 v súlade s usmernením WU
1 Rolle na 100 m
.
The product is supplied on a 100 m reel.
Bind the hose with filament tape and use a suitably sharp tool to cut the hose to the required length.
Injection circuits must not exceed 8 m in length.
After the hose has been cut to length, screw the respective connecting pieces fully into the hose (as far as they will go) - the image shows our fastening packers.
Place the hose centrally in the construction joint, within the reinforcement.
The surface of the construction joint must be clean, level and free of burrs, defects and loose particles of dirt.
The hose can be fastened in place with metal clips for nailing (manual or nail gun).
The distance between the fastening clips must not exceed 15 cm.
Alternatively, the hose can be fastened in place with plastic clips, either set in the fresh concrete or subsequently hammered into an 8 mm drill hole.
The distance between the fastening clips must not exceed 15 cm.
The hose must be in continuous contact with the concrete and must not be allowed to float.
Fixing on joints with category "rough"
On construction joints with a rough surface, fastening with a fastening grid is necessary to ensure full-surface support on the construction joint. The fixing grid is placed over the hose and fixed alternately (to the left and right of the hose) with nail plugs every 15 cm maximum.
Successive injection hose sections must overlap by at least 20 cm in order to ensure continuous injection of the joint.
All changes in direction must be implemented with a sufficiently wide bending radius in order not to damage the hose/restrict the overall injection flow.
The minimum radius is 5 cm.
The injection and ventilation ends can be kept in storage boxes, or alternatively the hose end can be attached to the formwork itself using fastening packers. The storage boxes or fastening packers must be arranged so they are easily accessible in the event of subsequent injection procedures (take high floor structures into consideration).
Once the concrete has cured, the resin can be injected via the fastening packers or the injection end pieces.
Status: 23.03.2022
HOSE CONNECTOR / VENTILATION HOSE / SEALING PLUG / STORAGE BOX in in-situ concrete
Stiahnuť DWG Stiahnuť PDFPríslušenstvo
vhodné príslušenstvo
Upevňovací púzdro MASTERTEC umožňuje upevniť injekčnú hadicu priamo na debnenie. Upevňovací packer umožňuje hospodárne upevnenie ...
Upevňovacia spona na inštaláciu vstrekovacích hadíc na betónových povrchoch odolných proti vztlaku ...
Polyuretánová živica na vstrekovanie do hadíc a vstrekovanie trhlín ...
Podobné produkty
Podobné produkty nájdete tu.
Tesnenie škár betónových konštrukcií kladie vysoké nároky na technológiu tesnenia.MASTERTUBE "YELLOW" zabezpečuje bezpečné...
Kontaktujte nás
Radi vám odpovieme na vaše otázky