Cinta para juntas de construcción con sellado hinchable activo
número de artículo 080646
La cinta para juntas de PVC activo MASTER-MultiFlex (MMF 140) con un perfil de hinchamiento adicional garantiza que las juntas de construcción de hormigón queden selladas de forma segura y permanente contra el agua de presión y no presión.
Añadir a la lista de avisosLa información más importante de un vistazo
Cinta de unión: PVC blando
Perfil de origen: TPE
Perfil de hinchamiento: blanco
Cinta de unión: ondulada
Perfil de origen: liso
25 m / Rolle
140 mnm
aprox. 6 mm
Certificado de prueba de la autoridad general de la construcción (AbP)
MPA Braunschweig
Ja
Utilizar clase A para clase de carga 1 y 2 de acuerdo con la directriz WU
No
Ja
Each carton contains 1 roll of MASTER-MultiFlex (MMF 140) and mounting brackets.
MASTER-MultiFlex (MMF 140) is placed on the upper reinforcement layer in the centre of the rising wall.
Place the mounting brackets (2 pcs/m), over the joint tape and fix them with binding wire to the upper reinforcement layer.
The embedment depth in the concrete must be at least 3 cm.
A white marking strip is provided on the MASTER MultiFlex (MMF 140) to check the embedment depth.
The MASTER-MultiFlex (MMF 140) can be cut to length easily with a cutter.
Due to its material properties, the MASTER-MultiFlex (MMF 140) is stable/ non-sagging but still very flexible.
All common geometries can be made.
Closed MASTER-MultiFlex (MMF 140) system.
Bonding options:
Welding:
For the welding process, the swelling profile can remain in the MASTER MuiltiFlex (MMF 140).
The corrugations of the MASTER-MultiFlex (MMF 140) ends to be joined fit into one another (peak into trough).
A hot air gun is used to weld the joint tapes together, one below
the other, with an overlap of 15 cm.
Adhesive join:
Mark an area of 75 mm on the ends being joined.
Grind down the corrugations in the bonding area with a grinding disk.
The swelling profile remains in the MASTER-MultiFlex (MMF 140).
Make sure that the smooth flanks on both side of the swelling profile are not ground away.
Prepared ends before bonding.
Surfaces free from interfering profile and visible soiling.
Apply the MMF 140 adhesive tape (width 75 mm), from the MMF
140 adhesive joining kit, on one side of Master-Multiflex (MMF 140) and remove the backing.
Press both ends, one prepared with MMF 140 adhesive tape, one without adhesive tape, together and bond them.
The join area must be secured with the MMF 140 fixing clip.
Secured joint tape with bonded joint.
Screwed connection:
The connection of two MASTER-MultiFlex (MMF 140) ends can also be made quickly and securely with an MMF 140 MASTERConnect "active".
The two ends of MASTER-MuiltiFlex (MMF 140) are - without prior processings - inserted into the MMF 140 MASTER-Connect „active“ on the left and right up to the screws, the screws are tightened to approximately 8 Nm.
Secured joint tape with MMF 140 MASTER-Connect „active“
Connection of SRF 125 crack-inducing profiles:
Use a grinding wheel to grind down the corrugation in the area in
which you wish to attacheon the crack-inducing profile.
The area to be ground must have a size of at least 160 x 75 mm.
Apply the MMF 140 adhesive tape on the prepared surface. Remove the backing before bonding with the crack-inducing profile.
Bond the crack-inducing profile with the prepared surface of MASTER-MultiFlex (MMF 140) on the water-facing side.
The bonding area must additionally be secured with 2 fixing clips.
Status: 23.03.2022
Accesorios
accesorios adecuados
El MMF 140 MASTER-Connect "activo" es una forma sencilla, rápida y segura de conectar in situ los extremos MASTER MultiFle...
Contacto
Estaremos encantados de responder a sus preguntas